ProStart CT-3371 Instalační příručka stáhnout pdf (Strana 3)

Quick installation Guide http://www.prostart.org P.3

PROGRAMMING THE TRANSMITTER TO THE MODULE

1. In programming mode (page 3) - the parking lights will stay on for up to 20 seconds.

2. Before the lights go out, turn the ignition key to OFF (if not OFF already), then ON, then OFF.

3. Press and hold the button until the parking lights flash 5 times quickly (unit will click).

4. The transmitter has been stored in memory. Each unit can store 4 remotes in its memory.

5. You have 20 more seconds to select one of the sub-menus if needed.

To program a transmitter on the second vehicle for multi-car operation;

press the button (instead of ) in step 3 of the transmitter association procedure.

ENTERING PROGRAMMING OPTIONS

1. In programming mode (page 3)



the parking lights will stay on for up to 20 seconds.

2. Before the lights go out, press and hold the brake pedal and then press one of the following buttons.

x LOCK to access mode 1;

x UNLOCK to access mode 2;

x TRUNK to access mode 3

3. The parking lights will flash 1, 2 ou 3 times to confirm entry into a mode.

4. Release the brake pedal.

Once the desired mode has been selected, the unit will fall (by default) into function #1 of that mode; you can

now select the option you want in function 1. Once this option has been chosen, the unit will move on to

function 2 of the mode selected, and so on.

x LOCK to access option 1;

x UNLOCK to access option 2;

x TRUNK to access option 3;

x START/STOP to access option 4.

5. After the programming of any mode is completed, the parking lights and the LED on the antenna will turn

ON for 20 sec. During those 20 seconds, select one of the sub-menus if needed.

PROGRAMMING OPTIONS

MODE 1

* INDICATES DEFAULT SETTING

FUNCTION 1 – Ignition-controlled door locks

OPTION 1* Ignition lock DISABLED

OPTION 2 Ignition lock ENABLED

FUNCTION 2 – Secure Lock

OPTION 1* Secure lock DISABLED

OPTION 2 Standard secure lock ENABLED

FUNCTION 3 – Starter Kill

OPTION 1* Passive arming (60 sec.)

Entering programming mode using the

Hood Pin

Entering programming mode using the

A.P.B. (Optional)

x Press and hold the hood pin down for 4 seconds. x Make sure the hood is closed.

x Release the hood pin.

The parking lights will turn ON for 1 second.

x Turn the ignition key to the IGNITION ON (RUN)

position.

x While the parking lights are ON, press the hood pin

once more and release immediately.

The parking lights will turn ON and stay ON for

20 seconds. You now have 20 sec. to select a

submenu.

x Within 5 seconds, press the programming button

on the antenna twice for 1 second each time.

The LED will come ON solid for 20 sec.

x You now have 20 seconds to select one of the

sub-menus.

Note 1: To exit programming mode, close the hood.

Note 1: To exit programming mode, press on the

antenna button once (the LED will come ON) and

release.

Note 2: For vehicles that require the ignition to be turned ON to activate the brake circuit, follow these steps to

select a submenu:

x After flashing the hood, turn the ignition ON and wait for the parking lights to come ON. Then,

press the brake pedal to access the sub-menus.

1 2 3 4 5 6

Komentáře k této Příručce

Žádné komentáře

ProStart CT-3371 Instalační příručka Strana 3

Komentáře k této Příručce

Související produkty a manuály pro Vzdálené spouštěče ProStart CT-3371